AMD Gpu Power maximun and Total Board Power
- Thread starter Vale902
- Start date
Not all time exactly but quite a lot
Here is a 3 hours gameplay session
Limit of the board is 375W
Max value is ~110W over the limit and average value about 80W over the average board power.
Last edited:
Hello Zach, thank you for your reply.
Mine seems to be spiking most of all the time during gameplay session.
I undervolted and lowered the clock to the stock stated on Sapphire, we use the same card.
Now I opened the game and the max valure is constant at around 200 - 220 W meanwhile TBP to 141W.
I will try to undervolt slightly more.
Mine seems to be spiking most of all the time during gameplay session.
I undervolted and lowered the clock to the stock stated on Sapphire, we use the same card.
Now I opened the game and the max valure is constant at around 200 - 220 W meanwhile TBP to 141W.
I will try to undervolt slightly more.
Attachments
Last edited:
With 2700MHz as top clock I bet you can go down to 1040~1050mV at least
Mine at 2850~2900MHz with demanding games needs 1070mV and less demanding games down to 1050mV.
Of course not all GPUs are exactly the same, even on same model as we both have.
Also dont look power maximum at non gaming apps. If you want to examine exactly what the GPU is doing try this
Get ready to run your game... First reset sensor values by clicking the clock (down on the right) and quickly start the game. Play at least 60min (longer if you use game menus frequently, like map, inventories and such). When finish and close the game, quickly take a screenshot of HWiNFO.
On the left side down corner you can use the arrows to have multiple columns visible like my screenshot.
Mine at 2850~2900MHz with demanding games needs 1070mV and less demanding games down to 1050mV.
Of course not all GPUs are exactly the same, even on same model as we both have.
Also dont look power maximum at non gaming apps. If you want to examine exactly what the GPU is doing try this
Get ready to run your game... First reset sensor values by clicking the clock (down on the right) and quickly start the game. Play at least 60min (longer if you use game menus frequently, like map, inventories and such). When finish and close the game, quickly take a screenshot of HWiNFO.
On the left side down corner you can use the arrows to have multiple columns visible like my screenshot.
What game is this?
Looks like its not consistently loading the GPU. Only 58.5% average GPU utilization.
If GPU load has large fluctuations then I think its normal to have bigger spikes.
I usually have 90+% average GPU utilization, so the load is more stable and so the power.
Looks like its not consistently loading the GPU. Only 58.5% average GPU utilization.
If GPU load has large fluctuations then I think its normal to have bigger spikes.
I usually have 90+% average GPU utilization, so the load is more stable and so the power.
I was playing monster hunter world (I use the texture pack too came by dlc, so it takes around 10gb VRAM), but, as stated earlier, I play with frame limiter because of my monitor is 100hz maximum. Gpu usage is never maxed out.Would be a waste of electricity and more heat otherwise for me.
My only concern are those bigger spikes and delta between tbp and the max power. I was expecting a low electric usage by not pushing higher the GPU too.
Last edited:
You do have low power consumption. Its only 163W by average.
The 251W is the average spike peaks not the avg power of the card.
Sorry for refloating this, but i'm ditching adrenaline for monitoring and trying to use this with riva tuner.
What's the power metric i should be following here, and which one is the GPU frecuency clock? i can't figure out for the life of me, and ppl around seem to be just as confused, some say shader effective, some say front end clock, and some say shader clock frecuency limit, which doesnt make any sense at all.
What's the power metric i should be following here, and which one is the GPU frecuency clock? i can't figure out for the life of me, and ppl around seem to be just as confused, some say shader effective, some say front end clock, and some say shader clock frecuency limit, which doesnt make any sense at all.
Attachments
just tried my new sapphire pulse 9070XT, the GPU max power is weird, the stock TBP is 304W and with stock setting or -50mV undervolting, my peak power is constantly hitting 500W whenever I try run 3D mark. It seems impossible even for spike to got 200W higher than the TBP cap? espeically with only 2x 8pin connection. Any idea where that reading comes from?
